FAQ
Also see FAQ Helmet Cameras/Camcorder connection
Are cameras difficult to install?
All kits are supplied with simple plug-in connections. The power is provided by a AC/DC 12 Volt mains adapter; this allows all connections, cable and camera to be low voltage, 12 Volts. The most difficult part of the exercise is hiding the cable. For info on installation go to DIY
What is a switcher?
Used in multiple camera systems, these inexpensive units sequentially switch from camera to camera for single camera viewing on a video monitor. Only the actual camera image being viewed on the monitor can be recorded. These units usually allow a camera's picture to be sequenced, bypassed, or held.
Can I connect the cameras to the monitor more than the 20metre cable supplied
Yes, the cable provided allows plug connections to join cables, several can be joined without problem.
Are TV's as good as monitors?
TV's are cheaper, there are more sold than monitors. You also have a TV tuner in addition to the monitor. TV's have audio and remote control. Monitors do have a better picture quality, especially if being used for high security applications. If being used for general observation a TV will work fine. It is worth noting that you normally cannot connect slave monitors to a TV. They must be interlinked and the camera signal modulated (by using a modulator, supplied with the Tele Secam System).
What is Scart or Phono?
All the cameras supplied will fit either the Scart or AV/Phono
Scart
socket
AV/Phono
socket
If you TV does not have Scart or Phono consider using your video and the TV via the video.
If both TV and video do not have Scart or Phono you will require a modulator (supplied with Tele Secam System), to allow you to convert the camera signal to RF. This will now allow you to use the normal aerial socket.
Connections to Cameras?
See DIY page
Will the Camera's work anywhere in the World?
The Output of the Cameras is Composite Video. They are PAL System. They will not work in the USA or Canada.
US and Canada uses NTSC system. If NTSC required please request.
Our Remote monitoring and digital record system an wireless systems are suitable for Worldwide use. They will work with PAL, NTSC and SECAM.
Will the Cameras plug into my TV or Video?
The Camera output is (Composite Video), the same as the SCART input of your TV or VCR.
Do you sell "Wireless CCTV Equipment"?
Yes, they match with any CCTV camera we sell - see wireless systems
Will the Cameras plug straight into the Aerial input of my TV or Video?
This will require a RF Modulator to convert from Video to RF
What voltage do the Cameras require?
The Cameras work on 12V DC, the Power Supply that comes with the Camera Kit's, will power up to 2 Cameras.
What is Polarity of the Cameras?
All the Cameras which have a 12 DC Socket on it are: Centre Pin Positive.
What does the standard 3.6mm lens see? (or 4.3mm supplied with 27C, as standard)
See Lens calculator
Is this camera suitable as a helmet cam - for motorcyclists, etc?
Yes - see feedback customer comment page, and also :
http://www.motorcycle-dk.com/en/multimedia/ All movies at Nüburgring, filmed at, or after September 9, with the 21C.
Can I use the cameras with my camcorder?
Yes, depends on model. It must have AV IN.
Cameras with C or CS mount
Modern cameras and lenses are generally CS mount rather than C mount. With CS mount cameras both types of lenses can be used but the C mount lens requires a 5mm ring to be fitted between the camera and lens to achieve a focused image. With C mount cameras it is not possible to use CS mount lenses as it is not physically possible to mount the lens close enough to the CCD to achieve a focused image.
Do it Yourself
TV or Monitor? Lenses - advice
Compact camera connections
Easy DIY task.
All kits are supplied with simple plug-in connections. The power is provided by a plug in PSU (power supply unit) 12 Volt mains adapter; this allows all connections, cable and camera to be low voltage,12 Volts. The most difficult part of the exercise is running the cable. (Use wireless kit, if wiring is difficult)
Connections: For Bullet, Submergible and Mini-square (fitted with BNC plugs)
Mini Cam Kit (click to expand)
Bullet Cam kit (click to expand)
Waterproof kit (click to expand)
 | POWER -The adaptor, 12 volt is plugged in to a normal wall socket | ||||
| THE CABLE at TV END
| ||||
| CABLE at CAMERA END
|
20 metre cable
scart
plug
Now, switch on TV and watch the picture on AV, (automatically tuned to AV).
Switcher - connecting multiple cameras
The Switcher is easy to connect. 12 Volt adapter supplied, this will also provide power to the cameras.
| Output - connect to TV |
| 4 camera inputs - plug in up to 4 cameras |
| Dip switches - use only to set switcher when using alarm cameras, up/down for ON/OFF |
| Power IN from adapter |
The switcher is now set from the menu using the top buttons, on screen display. All self explanatory.
Distance from TV or monitor?
Cameras can work to 200 metres using normal cable. Longer distances require drivers, etc.
100 metre cable can be provided.
Contact us for advice
Still not sure - email contact us
Easy!
Always
